Tc-helicon VoiceWorks Plus Manual Manuel d'utilisateur télécharger pdf (Page 39)

Cut/Boost Range: Sets how much boost or cut to

apply to the low band. Range: -12dB to +12dB.

HiShelf: Sets the cutoff frequency above which the high

shelf EQ may be boosted or cut. Range: 80Hz - 16kHz

Cut/Boost Range: Sets how much boost or cut to apply

to the high band. Range: -12dB to +12dB.

Q3: Parametric mid controls

MidParaEQ: (Mid band parametric EQ) Sets the center

Frequency in Hz. Cut/Boost Range: -12dB to +12dB.

Q: This value is equal to the center frequency of the

filter divided by the difference between the upper and

lower -3dB frequencies. The higher the Q value the

narrower the filter. Range is .1 (shown as Wide) to 10

(shown as Thin).

Q4: LowCut and gate controls

LowCut: (Low cut) This feature reduces rumble and

excess low frequency which can cause muddy sound.

The “knee” is 12dB per octave. Cutoff frequency

options include 60, 80 and 120Hz.

NoiseGate: Sets the threshold at which the noise gate

opens to allow sound through. If this is set above the

input level indicated on the led ladder, no sound will be

heard.

U0 to U5 - User Settings

U0: Global settings

GlblFX: (Global effects on/off) The Global Effects

parameter allows you to re-assign all presets to the

effect settings in a single preset of your choice.This is

to keep one effects setting across multiple presets.

Chord/Key: (Global chord and key) The Global Chord

and Key setting works much like the Global Effects

setting only for musical input. When you change and

save a key and scale in any Scale-based preset, all

presets will now be based on this setting. For Chord

mode presets, the last chord received at the MIDI

inputs is the first chord all Chord mode presets will

produce harmony from.

U1: Dry delay and tuning reference

DryDelay:Turning this On delays the lead vocal slightly

so the harmony voices will sound at the same time as

your lead voice. Turning this Off results in the least

amount of lead voice processing delay.

Tuning: This sets the overall tuning reference with

respect to A-440.

U2: Chord mode configuration

Chord Mode: The Classic setting sets the standard

Chord mode operation where any MIDI notes played

will be interpreted by the chord detection algorithm. In

Improvise chord mode, only 3 note chords trigger the

chord detection algorithm allowing more freedom in

playing keyboard parts and controlling harmony at the

same time.

U3: Notes Mode configuration

Selects between 1 Channel and 4 Channel notes mode

for all Notes presets in the product.

U4: Footswitch assignments

Footswitch 1-2-3: Allows custom assignment of

parameters to the Switch3 three button footswitch.

None: no assignment

Pre- : preset down

Pre+ : preset up

Byp: bypass

EffL: effect on/off latching

EffM: effect on/off momentary

HarL: harmony on/off latching

HarM: harmony on/off momentary

CorL: correction on/off latching

CorM: correction/off momemtary

Hold: enables the Harmony Hold feature (described

in the Harmony Background and Tips chapter)

U5: Effects priority

Lead FX Priority:When using Lead Model presets at 48

kHz sampling rates, VoiceWorksPlus does not allow

uMod and Transducer to be enabled simultaneously.

The parameter sets which effect gets priority upon

preset or effect load if both are activated in the preset.

M0 to M3 - MIDI Settings

M0: MIDI settings

MidiCh: (MIDI channel assignment) Sets the input MIDI

channel for harmony and CC messages. When set the

same as incoming MIDI such as that from a keyboard,

the front panel MIDI led will flash.When the channels

do not match the led will not respond.

Filter: Allows MIDI Program Change or System

Exclusive messages to be ignored for convenience.

THE SETUP MENU

1 2 ... 34 35 36 37 38 39 40 41 42 43 44

Commentaires sur ces manuels

Pas de commentaire

Tc-helicon VoiceWorks Plus Manual Manuel d'utilisateur Page 39

Commentaires sur ces manuels

Produits connexes et manuels pour Audio Tc-helicon VoiceWorks Plus Manual