Tc-helicon VoiceWorks Plus Manual Manuel d'utilisateur télécharger pdf (Page 38)

IO to I4 - Inputs/Output

I0: Input sensitivity

MicSens (Microphone sensitivity) This allows further

adjustment of microphone input sensitivity. Normal is

best for the majority of microphones. However, the

Low and High settings can be useful for extra high

output or extra low level microphones.

LineSens (Line input sensitivity) Sets the Line input

sensitivity, or maximum input level from 0dBu to 24dBu

to match with your mixer. The factory default setting

of 15dBu is an average output level from most mixers.

Adjust this up or down when you see the input meters

consistently low or in the red.

I1: Digital input gain

Digital In Gain: Here the digital in signal can be

attenuated to reduce clipping. 0dB is unity and is the

ideal setting.

I2: Input source and clock settings

Input: Here you select the Analog or Digital input.

Selecting Analog input will use the input selected via

the front panel (Mic or Line). Digital input will use the

rear S/PDIF connectors. The digital output is always

available regardless of this setting.

ClockSrc: (Clock source) This sets the audio clock

frequency and source. If using the analog inputs, this

parameter is best set to Int(ernal) 44.1. If you are using

the digital input you should set this to sync to

Ext(ernal) clock. If no valid clock signal is recieved via

the digital inputs, an error message will be shown.

I3: Output and bypass mode

Output: Collapses all stereo output to mono if desired.

BypMode: (Bypass mode) This sets how

VoiceWorksPlus operates in Bypass. The Stage setting

preserves any EQ and Dynamics settings you have set

and matches the level of the Dry voice.

The Studio setting removes all effect processing

including the EQ and Dynamics and outputs the lead

signal at full level to the output.

I4: Input on/off controls

Dry VoiceIn: Setting this to Off removes the dry lead

audio from the signal path in any presets that mix in

your dry voice. This is useful when using

VoiceWorksPlus on an auxilliary mixer send and want

100% wet output.

AuxIn: (Auxilliary input) Setting this to Off removes

the dry Aux Input audio from the signal path. This

allows VoiceWorksPlus to produce only 100% wet

effects when receiving an effects send from a mixing

board into the Aux Input. (Only available in analog

input mode if Mic Input is selected)

Q0 to Q4 - EQ/Compressor

The EQ and compressor in VoiceWorksPlus are global

meaning that all presets will be affected once either of

the compressor or EQ has been activated. Be careful

when adjusting these parameters because feedback is

more likely.

Q0: EQ and compressor assignment

DynAssign: (Dynmics assignment) This allows you to

assign dynamic processing (compressor and gate) to

the lead voice, harmony/model voices, both lead and

harmony/model voices or neither. Hint: assigning only

to the lead voice with a medium compressor setting

(threshold: -15dB, ratio:2:1) keeps the lead voice a

consistent volume but keeps harmony levels following

the singers level. This gives control of harmony levels

with mic technique.

EQAssign: (EQ assignment) This allows assignment of

the three band EQ to the lead voice, harmony/model

voices, both lead and harmony/model voices or neither.

Q1: Compressor controls

The compressor in VoiceWorksPlus has automatic

makeup gain to a maximum of +20dB.This means that

the volume level of the signal will be increased for most

volume levels of input with the compressor enabled.

Threshold: Sets threshold at which the compressor

becomes active level from 0 to -60 dB. A moderate

setting of -6 to -15 works well.

Ratio: Sets your compression ratio range from 1.12:1

to 64:1. This sets how much level reduction occurs

once the input signal reaches the threshold you have

set.

Q2: EQ settings

VoiceWorksPlus has a flexible 3 band EQ with

frequency-adjustable high and low shelving bands and a

fully parametric band with Q, frequency and gain

controls.

LoShelf: Sets the knee frequency for the low frequency

shelving boost or cut. Frequency Range: 80Hz to

16kHz

THE SETUP MENU

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 44

Commentaires sur ces manuels

Pas de commentaire

Tc-helicon VoiceWorks Plus Manual Manuel d'utilisateur Page 38

Commentaires sur ces manuels

Produits connexes et manuels pour Audio Tc-helicon VoiceWorks Plus Manual