Tc-helicon VoiceWorks Plus Manual Manuel d'utilisateur télécharger pdf (Page 34)

X1: Sends to the effect blocks

The outputs of each of the Dry voice, Lead

modeling/Harmony, and Auxilliary input paths can be

routed to the effects here.This is where you can adjust

the balance of reverb applied to your dry voice versus

how much reverb is sent to the harmony voices for

example.

In order for an effect to be audible, both the send and

return levels need to be set. Default send levels have

been set for each expected effect configuration.

Send: Turning the soft knob associated with this

parameter determines which effect you wish to adjust

the sends for. As you turn the knob, the send settings

for each effect are shown in the display.

Lead: This is where you send your dry voice to the

effect selected with the Send parameter.

H/M: (Harmony and Lead Modeling sends) This is

where you send to the effects from either of the

Harmony block or the Modeling block depending on

the configuration of the current preset.

Aux: (Auxilliary input send) You can apply effects to any

audio signal received at the Line Input when you have

a mic plugged into the Mic Input.

X2: Effect returns

These parameters allow you to adjust the relative level

balance and stereo width of each of the three effects

blocks. If the send level is 0 for any of the parameters

in the send screen, turning up the returns in these

screens will have no effect.

Out: Turning the soft knob associated with this

parameter selects either the level for each effect block

or the stereo width. Note that for some effects like

mono delays, adjusting the Width will have no effect.

Unless you specifically prefer mono effects, this is best

left Stereo. If you are using VoiceWorksPlus with a

mono sound system, you can set the global

Mono/Stereo parameter to Mono in the Setup menu.

Mod, D ly(Delay), and Rev(erb): These allow you to

bring the output of these effect blocks into the main

mix and to balance their levels.

Mod block editing menus M0-M8

These menus allow to select styles and perform

customization on this block.

Mod is short for micro-modulation (" " is the

REVERB, MOD AND DELAY EDITING

Chapter Overview

This chapter discusses editing of the “classic” effects

blocks that produce Reverb, Mod and Delay. In

VoiceWorksPlus, these three effects are only available

in a parallel or aux send-type configuration meaning

they are added to the effect in a maximum 50/50 mix

of wet and dry, never 100% wet.

Because the application of these types of effects is

largely understood, we’ll discuss only the editing

parameters and not their usage.

The Transducer effect functions slightly differently and is

discussed separately in the next chapter

Effects editing is discussed briefly in the Editing

Overview chapter.

The method for adding effects is typically thus:

o Decide which effect you would like to add.

o Decide which of the input paths from the Dry,

Harmony/Lead Modeling or Aux input that you

would like hear to the effect added to.

o Check or raise the send level for that input path.

o Raise the level of the return from the effect

you’ve selected.Also, make sure the FX led on

the front panel is lit.

o Go to the style selection screen for the effect

you’ve chosen and choose a style that sounds

close to what you want to hear.

o Edit the effect style or parameters if you prefer.

Note that if Global FX is activated any editing you do

will appear to be applied to the current preset but will

actually be applied to the preset designated in the

Global FX menu in Setup.

Effects mixing menus X0-X2

These screens allow you to adjust the send and return

levels of the effects blocks. As always, 0dB means “full

level”.

X0: Crossover feeds to Delay and Reverb

Mod2Del: (Micromod send to Delay) This allows you

to route the output of the Mod block to the input of

the Delay block.

Del2Rev: (Delay send to Reverb) You can route the

output of the Delay block to the Reverb block input.

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

Tc-helicon VoiceWorks Plus Manual Manuel d'utilisateur Page 34

Commentaires sur ces manuels

Produits connexes et manuels pour Audio Tc-helicon VoiceWorks Plus Manual